Replacing the screen on an OPPO Find X5 can restore a cracked or unresponsive display, but it requires precision and the right tools. This guide walks you through the entire process, from preparation to final testing. Always work in a clean, well-lit area and take antistatic precautions. If you are not confident, consider professional repair — but with patience and the steps below, many DIY enthusiasts can succeed.
Tools and Materials Needed
Before starting, gather the following items. Using the correct tools reduces the risk of damaging internal components.
Precautions and Safety
Working with lithium-ion batteries and delicate displays carries risks. Follow these safety measures:
- Power off the device completely before starting.
- Discharge the battery to below 25% to reduce fire risk if punctured.
- Avoid excessive heat — use a heat gun on low setting (around 80°C) and keep it moving.
- Do not pry near battery — use plastic tools to avoid short circuits.
- Ground yourself to prevent static discharge damaging components.
- If you encounter resistance, reapply heat and try again — don’t force anything.
Step-by-Step Screen Replacement
1. Remove the Back Cover
The OPPO Find X5 has a glass back that is glued on. Heat the edges with a heat gun or hair dryer for about 2 minutes until the back feels warm. Use a suction cup to lift a gap, then insert a plastic opening tool. Slide the tool around the perimeter to cut the adhesive. Be careful near the camera module and volume buttons. Once all adhesive is loose, lift the back cover off and set it aside.
2. Disconnect the Battery
Inside, you’ll see the motherboard cover held by screws. Remove the screws (note their positions — use a magnetic mat). Lift the cover off. Locate the battery connector (a large flex cable) and gently pry it up with a spudger. This disconnects power from the phone. Always disconnect the battery first before working on other components.
3. Remove the Motherboard (if necessary)
On the OPPO Find X5, the screen connector is under the motherboard. You may need to remove the motherboard to access it. Disconnect all flex cables: display, touch, front camera, and any others. Note: the rear camera module is attached; you can leave it in place if you only lift the board slightly. Remove the screws securing the motherboard (tri-point Y000). Gently lift the motherboard from the bottom edge, tilting it upward. Do not bend it excessively.
4. Disconnect the Broken Screen
With the motherboard lifted, locate the two flex cables for the screen (display and touch). They are usually side by side. Carefully disconnect them using a spudger. Now the screen is free from the logic board.
5. Remove the Broken Screen
The screen is glued to the frame. Heat the front edges thoroughly for 3-4 minutes. Use a suction cup on the screen (near the bottom edge) and pull gently. Once a gap appears, insert a plastic pick and slide it around to separate the adhesive. Work slowly — the OLED panel is fragile. If the glass is shattered, tape over it to prevent shards from flying. Lift the screen off and dispose of it properly.
6. Clean the Frame
Remove all old adhesive residue from the phone’s frame using isopropyl alcohol and a lint-free cloth. Ensure the surface is smooth and free of glass splinters. Use tweezers for stubborn pieces. A clean surface ensures proper adhesion of the new screen.
7. Install the New Screen
Peel the protective film from the new screen’s adhesive (if pre-applied) or apply thin adhesive strips around the frame. Carefully align the screen’s flex cables with the openings in the frame. Lower the screen into place, pressing gently along the edges to secure it. Do not press on the center of the display — it may damage the OLED panel.
8. Reconnect Everything
Reattach the screen cables to the motherboard. Lower the motherboard back into position and secure it with screws. Reconnect the battery connector. Replace the motherboard cover and its screws. Finally, reattach the back cover — apply adhesive strips or B-7000 glue along the frame, press the back cover on, and hold with rubber bands for 30 minutes to set.
Testing the New Screen
Before sealing the back cover permanently, power on the phone to test the new screen. Check for:
- Touch response across the entire screen.
- Display colors, brightness, and dead pixels.
- Proximity sensor and auto-brightness (if applicable).
- Fingerprint scanner (if under-display) — may need recalibration via software.
If any issues arise, double-check cable connections. If the touch is unresponsive, ensure the touch flex is fully seated.
Troubleshooting Common Issues
Even with careful work, problems can occur. Here are common fixes:
- Screen not turning on: Check battery connection; ensure screen cables are fully inserted and not damaged.
- Touch not working: Re-seat the touch flex; verify the correct screen model (OPPO Find X5 uses a specific flex layout).
- Backlight uneven: This may indicate a defective screen — contact supplier for replacement.
- Phone overheating: Ensure no screws are missing or misplaced, and that all connectors are properly grounded.
For more complex issues, such as water damage after a repair, see our guide on Samsung water damage repair (similar principles apply).
Where to Get Parts and Help
In the Netherlands, you can find OPPO Find X5 screens at ReparatieParts.nl (€89.95) or iFixit (€129.99). If you prefer professional installation, many repair shops in Amsterdam, Rotterdam, and Utrecht charge around €100-€150 for labor. For a comprehensive overview of DIY phone repair in the Netherlands, read The Complete Guide to DIY Phone Repair in the Netherlands.
While this guide focuses on the OPPO Find X5, similar techniques apply to other models. For example, our Samsung Galaxy S22 screen repair guide covers a comparable process, though internal layouts differ. Always check model-specific details before starting.
Related Articles