The Samsung Galaxy S22, released in February 2022, features a 6.1-inch Dynamic AMOLED 2X display with a 120Hz refresh rate. Despite its durability, accidental drops or impacts can shatter the glass or damage the OLED panel. This guide provides a detailed walkthrough for replacing the screen yourself, covering tools, costs, and common pitfalls. If you are not confident in your repair skills, consider professional help or read our complete guide to DIY phone repair in the Netherlands.

Tools and Materials Needed

Before starting, gather the following tools and parts. Using the correct tools prevents damage to delicate components.

  • Replacement screen assembly (with frame pre-installed) – available from iFixit, ReparatieBudget, or Amazon.nl for €150–€250 depending on quality.
  • Pentalobe P2 screwdriver – for the two bottom screws near the charging port.
  • Phillips #00 screwdriver – for internal screws.
  • Plastic opening tools – spudger, pry tool, and suction cup.
  • Heat gun or iOpener – to soften adhesive.
  • Tweezers – for handling small screws and connectors.
  • Isopropyl alcohol (90%+) – to clean adhesive residue.
  • Adhesive strips or B-7000 glue – for resealing the screen.
  • Magnetic mat – to organize screws by location.

Always power off the device and remove the SIM tray before starting. For more details on charging port repairs, see our guide on iPhone Charging Port Fix (similar principles apply).

Step 1: Remove the Back Glass

The Samsung Galaxy S22 uses a glass back that must be removed first because the screen is glued to the midframe. Unlike some models, the S22 does not have a removable back cover; you must heat the adhesive.

  1. Heat the back glass evenly with a heat gun at ~80°C for 2-3 minutes, or use an iOpener for 5 minutes.
  2. Apply a suction cup near the bottom edge. Pull up gently to create a small gap.
  3. Insert a plastic pry tool into the gap and slide it along the edges to cut the adhesive.
  4. Lift the back glass carefully. Note the wireless charging coil attached to it – do not yank.
  5. Set the back glass aside. You may need to replace the adhesive if it loses stickiness.

Be careful not to crack the back glass; replacements cost around €30–€50.

Step 2: Disconnect the Battery and Remove Components

Safety first: disconnect the battery to avoid short circuits. The S22 battery is soldered to the motherboard, but you can disconnect the flex cable.

  1. Locate the battery connector on the motherboard (lower right corner). Use a plastic spudger to gently pry it up.
  2. Remove the screws securing the motherboard shield (Phillips #00). There are 8 screws in total: 4 on the upper shield and 4 on the lower.
  3. Lift the shield with tweezers. Note the placement of the loudspeaker module – it is glued.
  4. Disconnect the display flex cable (two connectors: one for the screen, one for the digitizer) using a spudger.
  5. Remove the front-facing camera and earpiece speaker if they are attached to the old frame (they often stay with the frame).

For reference, the iPhone screen replacement process is similar in disconnection steps. See our iPhone Screen Replacement Guide for a comparable procedure.

Step 3: Remove the Old Screen

The S22 screen is glued to the midframe. If you purchased a screen with a pre-attached frame, you can skip this step and simply transfer components to the new frame. However, if you are replacing only the glass (not recommended for amateurs), follow these steps.

  1. Heat the front of the phone with a heat gun at 80°C for 3 minutes.
  2. Apply a suction cup to the screen and pull up. Insert a pry tool to cut the adhesive.
  3. Work your way around all four edges. The adhesive is strong; take your time.
  4. Once the screen is free, lift it away. The OLED panel is fragile – do not bend.
  5. Remove any remaining adhesive from the midframe using isopropyl alcohol and a plastic scraper.

If the screen is cracked, wear gloves to avoid glass splinters. Dispose of the old screen properly at a recycling center.

Step 4: Install the New Screen

Before applying adhesive, test the new screen by connecting it to the motherboard without fully seating it.

  1. Connect the display flex cables to the motherboard. Press gently until they click.
  2. Reconnect the battery and power on the phone. Check for touch response, color accuracy, and brightness.
  3. If the screen works, power off and disconnect the battery again.
  4. Apply pre-cut adhesive strips or a thin line of B-7000 glue to the midframe edges. Avoid the camera and sensor areas.
  5. Place the new screen onto the frame, aligning the top edge first. Press down firmly along all edges to secure the adhesive.
  6. Reinstall the motherboard shield and screws. Torque to 0.5 Nm – do not overtighten.

Sealing the phone properly is crucial to maintain water resistance (IP68 rating). The adhesive must be continuous and free of gaps.

Step 5: Reattach the Back Glass

Clean the back glass and midframe with isopropyl alcohol. Apply new adhesive (pre-cut or B-7000) to the midframe. Align the back glass over the wireless charging coil and press firmly. Use rubber bands or clamps to hold the back glass in place for 24 hours while the adhesive cures.

Common Issues and Troubleshooting

  • Screen flickering or no display: Check that the display cable is fully seated. If not, reconnect. If still flickering, the replacement screen may be defective.
  • Touch not working: Ensure the digitizer cable is connected. Calibrate the touchscreen via the service menu (dial *#0*#).
  • Proximity sensor not working: The sensor is located near the earpiece; make sure it is not blocked by adhesive.
  • Water resistance lost: Use high-quality adhesive and allow full curing time. Consider a professional seal if you need IP68 restoration.

If you encounter issues with the charging port during disassembly, our iPhone Charging Port Fix guide offers useful tips for cleaning and replacing USB-C ports.

Cost Comparison: DIY vs. Professional Repair

In the Netherlands, official Samsung repair centers charge €350–€400 for a Galaxy S22 screen replacement. Third-party shops like ReparatieBudget or iRepair in Amsterdam charge €200–€300. DIY costs range from €150 (lower-quality screen) to €250 (original Samsung part) plus €20–€30 for tools. DIY saves you €50–€150 but voids warranty and carries risk. If you are not experienced, consider using a professional service.

For more background on repair economics, see our complete guide to DIY phone repair in the Netherlands.

Related Articles

  • iPhone Screen Replacement Guide (iPhone 12)
  • iPhone Charging Port Fix
  • The Complete Guide to DIY Phone Repair in the Netherlands
  • Samsung Galaxy Battery Replacement Guide
  • Samsung Galaxy Back Glass Repair Guide